01242 584490

07973 624488

enquiries@mainpoint.co.uk

Want us to phone you?

Free Newsletter?

Feeling Sociable?

ASFP Guidance Notes Use of Polyurethane Foams

May 24th, 2016

ASFP Guidance Notes Use of Polyurethane Foams

GENERAL PROPERTIES OF PU FOAMS
PU foams are normally expelled from pressurised cans through long nozzles as a sticky liquid which quickly expands by typically 40 times its original volume to form rigid foam. PU foams are not structural materials and hence should not be used in areas subject to foot traffic where such traffic is likely to pass over the seal and transfer load to the seal material.
FIRE PROPERTIES 4Reaction to Fire Many PU foams claim to be ‘Fire Rated’ often citing e.g. a Class 0, Class B1 or similar performance when tested against British or European standards. These classes are ‘reaction to fire’ classifications which are concerned with the ignitibility, surface spread of flame and heat release characteristics of the material. Reaction to fire classifications cannot support the use of the material where fire resistance is required, such as in linear gap or service penetration seals. 4Fire Resistance Fire resistance, in the context of PU foams, is the ability of a wall or floor to maintain fire separation so that fire does not spread from one compartment to another. PU foams which are to be used in linear gap or service penetration applications must have their fire performance determined by testing to the appropriate national or European fire resistance test Standards. In the UK the appropriate Standard is BS 476: Parts 20/22, BS EN 1366-4 in the case of linear gaps and BS EN 1366-3 for service penetration seals. Once tested to the required Standard(s) it is important that the scope of application of the test results is assessed by a competent person or organisation in accordance with current industry agreed guidance and that the products are not used outside of the scope of such guidance without further support from expert opinion. For example, PU foams tested as linear gap seals cannot be used to seal pipe or cable penetrations (see photo) unless they have been tested in that end-use application. When CE marking of penetration and linear gap seals starts, extending the scope of application will be undertaken using Extended Application standards rather than assessments. CE marking is expected to be mandatory in 2013 when the Construction Products Regulation replaces the Construction Products Directive.
GUIDANCE IN USE
PU foams are combustible and hence the rate at which combustion occurs under standard heating conditions will be dependent upon such factors as the available oxygen and the presence of conductors capable of transferring heat into the seal. With respect to the former the aspect ratio (gap/opening width/seal depth) will be a key factor in determining fire performance. In the case of heat transfer the presence of penetrating metallic pipes or cables with large metallic conductors will have a detrimental effect on fire performance and should be seen to be within the scope of the assessed applications. UK guidance suggests that openings for small plastic pipes of 40mm o/d or less need only be fire stopped around the pipe without the need for the use of a pipe closure device or a metallic sleeve. In such circumstances it is important that the seal around the pipe is non-combustible so as to limit the size on any resultant opening in the fire separating construction and consequently the use of PU foam is not suitable. Plastic pipes may also be sealed by the use of intumescent wrap systems designed to expand under fire conditions crushing the softened pipe and sealing the opening. Such systems require external restraint in order that the intumescent expansion is directed inwards. Hence, if PU foam is to be used to seal an opening around such a device, evidence must be available which demonstrates the required fire performance under test. Finally, care should be taken where the bonding properties of the foam under fire conditions may be critical to the performance of another element, for example, if the foam were to be used to bond the frame of a fire resistant door into a structural opening without the use of additional mechanical fixings. In such a case the erosion of the foam as it burns is likely to significantly weaken the stability of the frame to the point where it has a detrimental effect on the fire performance of the door assembly. Hence, as with intumescent pipe wrap, proof of performance in the intended application must be available before use.

Exciting news!

Firecall has now merged with Cheltenham company Mainpoint.

Established in 1991, Mainpoint Fire Protection Ltd are award winning specialists in the supply, installation and maintenance of fire protection equipment, fire alarms and emergency lighting to businesses, residents and the public sector. Being a local company based in Cheltenham, Gloucestershire we are able to offer you a friendly and professional team of skilled staff in their particular field to provide quality workmanship, first-rate customer service and dependability gaining many prominent clients and hundreds of smaller customers.